поднял радиус по мануалу тестовый пользователь работал но после конфигурации sql.conf пользователей не видет в базе при вводе radtest babis 147852 127.0.0.1 0 hardpass5
выдаёт
rad_recv: Access-Request packet from host 127.0.0.1:18216, id=193, length=57
User-Name = "babis"
User-Password = "147852"
NAS-IP-Address = 255.255.255.255
NAS-Port = 0
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 7
modcall[authorize]: module "preprocess" returns ok for request 7
modcall[authorize]: module "chap" returns noop for request 7
modcall[authorize]: module "mschap" returns noop for request 7
rlm_realm: No '@' in User-Name = "babis", looking up realm NULL
rlm_realm: No such realm "NULL"
modcall[authorize]: module "suffix" returns noop for request 7
rlm_eap: No EAP-Message, not doing EAP
modcall[authorize]: module "eap" returns noop for request 7
modcall[authorize]: module "files" returns notfound for request 7
radius_xlat: 'babis'
rlm_sql (sql): sql_set_user escaped user --> 'babis'
radius_xlat: 'SELECT NULL, 'test', 'Password', '123456', '==''
rlm_sql (sql): Reserving sql socket id: 2
radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'babis' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id'
rlm_sql_mysql: MYSQL check_error: 1146 received
rlm_sql_getvpdata: database query error
radius_xlat: ''
radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'babis' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id'
rlm_sql_mysql: MYSQL check_error: 1146 received
rlm_sql_getvpdata: database query error
rlm_sql (sql): Released sql socket id: 2
rlm_sql (sql): No matching entry in the database for request from user [babis]
modcall[authorize]: module "sql" returns notfound for request 7
rlm_pap: WARNING! No "known good" password found for the user. Authentication may fail because of this.
modcall[authorize]: module "pap" returns noop for request 7
modcall: leaving group authorize (returns ok) for request 7
auth: No authenticate method (Auth-Type) configuration found for the request: Rejecting the user
auth: Failed to validate the user.
Delaying request 7 for 1 seconds
Finished request 7
Going to the next request
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Sending Access-Reject of id 193 to 127.0.0.1 port 18216
Waking up in 4 seconds...
--- Walking the entire request list ---
Cleaning up request 7 ID 193 with timestamp 4ba7c806
Nothing to do. Sleeping until we see a request.
вот файл sql.conf
#######################################################################
# Authorization Queries
#######################################################################
# These queries compare the check items for the user
# in ${authcheck_table} and setup the reply items in
# ${authreply_table}. You can use any query/tables
# you want, but the return data for each row MUST
# be in the following order:
#
# 0. Row ID (currently unused)
# 1. UserName/GroupName
# 2. Item Attr Name
# 3. Item Attr Value
# 4. Item Attr Operation
#######################################################################
# Use these for case sensitive usernames.
# authorize_check_query = "SELECT id, UserName, Attribute, Value, op \
# FROM ${authcheck_table} \
# WHERE Username = BINARY '%{SQL-User-Name}' \
# ORDER BY id"
# authorize_reply_query = "SELECT id, UserName, Attribute, Value, op \
# FROM ${authreply_table} \
# WHERE Username = BINARY '%{SQL-User-Name}' \
# ORDER BY id"
# The default queries are case insensitive. (for compatibility with
# older versions of FreeRADIUS)
authorize_check_query = "call radcheck('%{SQL-User-Name}')"
authorize_reply_query = "call radreply('%{SQL-User-Name}')"
accounting_update_query = "call radupdate('%{SQL-User-Name}')"
accounting_stop_query = "call radstop('%{SQL-User-Name}')"
}
процедуры mysql -p вроде прошол без ошибок
в чём может быть проблема
